HELASLIDE premium slider system

HELASLIDE camera slider: 800 mm & 1200 mm

One slider system in two lengths, plus custom sizes on request. Rotating base, built-in horizontal offset, low mode, swappable rails and magnetic dampeners, machined from hard-anodized 6061 aluminum in Vancouver.

HELASLIDE 800 mm and 1200 mm camera sliders side by side
Compare

800 mm vs 1200 mm rails

Same carriage, base and features. The difference is rail length, travel and weight. Prices in USD.

HELASLIDE · 31.5 in

800 mm rails

$4,800 USD

Fitted hard case available

Length
31.5 in (800 mm)
Travel
24 in (610 mm)
Weight
37 lb
Request a quote
HELASLIDE · 47.25 in

1200 mm rails

$5,200 USD

Fitted hard case available

Length
47.25 in (1200 mm)
Travel
39.75 in (1010 mm)
Weight
46 lb
Request a quote
Built to order

Custom size

Specs on request

Need a shorter or longer slider? HELASLIDE rails can be made from 23.5" up to 96".

Short
23.5 in (600 mm)
Long
71 in / 96 in
Pricing
On request
Ask about a custom size

Side-by-side specifications

Spec800 mm1200 mmCustom
Price (USD)$4,800$5,200On request
Fitted hard caseAvailableAvailableOn request
Rail length31.5 in (800 mm)47.25 in (1200 mm)23.5 in to 96 in
Travel24 in (610 mm)39.75 in (1010 mm)16 in (600 mm rails) to 88.5 in (2400 mm rails)
Weight37 lb (16.8 kg)46 lb (20.8 kg)32 lb (600 mm) to 72 lb (2400 mm)
Width8.85 in (225 mm) · 11.61 in (295 mm) including levers
Height3.85 in (98 mm) without Mitchell mount · 5.19 in (132 mm) with Mitchell mount
Rotating base360°+ continuous, locking
Horizontal offsetTool-free, locks in any position
Low modeMitchell mount removes tool-free, head under 4 in off the ground
Rail swapUnder 4 minutes with the included tools
IncludedTools for rail swaps and the Mitchell nut
HELASLIDE camera slider isometric render
Custom sizes

Need a different length?

The 800 mm and 1200 mm sliders cover most setups, but HELASLIDE rails can be built in other lengths. Specs for custom sizes are available on request.

  • 23.5" (600 mm) rails for tight spaces
  • 71" (1800 mm) and 96" (2400 mm) rails for long moves
  • A secondary base is recommended past 47.25"
  • Extra rail sets to swap onto your existing slider
Ask for custom specs
Features

Designed on set, for set

Every detail comes from years of camera and grip work on productions of every size.

Render of the HELASLIDE low-profile rotating base and Mitchell mount

Rotating base: 360° in any direction

The low-profile locking rotating base lets you change the direction of the slider on the fly, no matter where you stand. Continuous 360° of motion means you never run out of adjustment in any direction.

Render of the HELASLIDE base offset to one end of the rails

Horizontal offset, no extra gear

A slider and a horizontal offset in one. The entire base slides along the rails tool-free and locks in any position, even while the camera is still sitting on the slider. Dial in the shot without re-rigging. Don't be stuck with one position, have them all.

Render of the HELASLIDE upper carriage showing the rollers, carriage brake and bubble level

Precision rollers, silent moves

Chrome-plated rollers on precision-ground rod with sealed bearings, the kind of linear motion you find on high-end CNC machines. Moves are smooth and precise at any speed. A light push of a finger gets the carriage rolling for those slow crawls. Completely silent at slow speeds and whisper-quiet when you need to go faster. A carriage brake and bubble level are built in.

Render of the removable HELASLIDE Mitchell mount and low-profile Mitchell nut knob

Tool-free Mitchell mount and low mode

The Mitchell nut comes off tool-free with a specially designed low-profile knob that is easy to reach in the most awkward spaces. In less time than it takes to read this sentence, the bottom Mitchell mount can be removed, placing the head less than 4" off the ground for extremely low-profile shots.

Render of HELASLIDE rail sets in two lengths with carriage and base

All the sizes you will ever need

What's the ideal length for a slider? From shot to shot and show to show, it's hard to pick one size that works for every situation. With HELASLIDE your choice doesn't have to be final. The rapid-change system lets you swap to any length rails in less than four minutes with the included tools. On the ground, on sticks or on the dolly. One slider, every size. How it works

Close-up render of the HELASLIDE carriage on the rails

Magnetic dampeners

Magnetic dampeners at the rail ends soften the stop at the end of every move, so the carriage settles quietly instead of slamming into the end plates.

HELASLIDE mounted upside down under an overhead rig on a film set

Works upside down

Underslung from a dolly mount, hanging from a ceiling rig or strapped to a tree: HELASLIDE works right side up, sideways or inverted. Mounting holes on the sides, ends, top and bottom make rigging straightforward.

Changing length

Swap rails in under 4 minutes

  1. Remove the feet
  2. Unscrew 4 bolts
  3. Loosen 2 bolts
  4. Remove the end plates
  5. Slide the upper and lower carriage off the original rails
  6. Slide the upper and lower carriage onto the new rails
  7. Repeat steps 1 to 4 in reverse order

Rail sets: RA600, RA800, RA1200, RA1800 and RA2400. Upper carriage UA056, lower carriage LM001, side plate assembly RA134, Mitchell nut assembly LM005.

HELASLIDE rail end plate being removed to change rail length
In the box

What's included

  • HELASLIDE slider with your chosen rail length
  • The tools needed for rail swaps and the Mitchell nut

A fitted hard case is available for both sizes. Ask for pricing when you request a quote.

HELASLIDE camera slider dimensioned top-view drawing with travel distances, weights and mounting holes for every rail length
Top view, 800 mm rails shown. Travel distance and weight for every rail length from 600 mm to 2400 mm, plus mounting hole sizes. Click to enlarge.
PartMaterial
Body / frame6061 aluminum, hard anodized
Linear motionChrome-plated rollers, precision-ground rod, sealed bearings
FastenersStainless steel, zinc plated, black oxide
Various partsCarbon fibre PA06 nylon
FeetRemovable, adjustable rubber feet (70A)
MountAluminum Mitchell mount, tool-free low-profile Mitchell nut
LocationMounting holes
Carriage#10-24 (4×), 1/4"-20 (3×)
Knurled handle3/8"-16 thread (centered)
Sides (face)1/4"-20 (2×), 3/8"-16 (2×)
Ends1/4"-20 (1×)
Bottom3/8"-16 (3×)
Top3/8"-16 (2×)
FAQ

Common questions

What is the difference between the 800 mm and 1200 mm sliders?

The 800 mm HELASLIDE uses 31.5" rails with 24" of travel and weighs 37 lb. The 1200 mm HELASLIDE uses 47.25" rails with 39.75" of travel and weighs 46 lb. Both share the same carriage, rotating base, offset and features.

Can I get a custom length?

Yes. HELASLIDE rails can be made in other lengths, from 23.5" (600 mm) up to 71" (1800 mm) and 96" (2400 mm). Specs and pricing for custom sizes are available on request. A secondary base is recommended for rails longer than 47.25".

Do I need tools to offset the base or remove the Mitchell mount?

No. The horizontal offset is tool-free and locks in any position, and the Mitchell nut comes off by hand with its low-profile knob. The only tools you need are for swapping rails, and they come with the slider.

Can I change rail length later?

Yes. The carriage and base move between rail sets in under 4 minutes using the included tools.

Does it mount to a dolly or crane?

Yes. HELASLIDE uses a standard Mitchell mount with a tool-free, low-profile Mitchell nut, and it is used on set on J.L. Fisher dollies and cranes. It also works inverted and sideways.

What currency are prices in?

All prices are in US dollars (USD). Taxes and shipping are not included. Contact us for a full quote.

Where is HELASLIDE made?

HELASLIDE is designed and built by Kinemat in Vancouver, British Columbia, Canada.

Get a HELASLIDE quote

800 mm, 1200 mm or a custom length. We'll reply with pricing and availability.

Request a quote